Inside a Cold-Shrink Termination: Why Material, Interface and Test Data Decide Service Life
Nov 11, 2026| Inside a Cold-Shrink Termination: Why Material, Interface and Test Data Decide Service Life
Industry knowledge series - medium-voltage cable accessories
Most medium-voltage cable failures do not start in the cable. They start at the termination, and usually at one of three places: the screen cut-back where the electric field concentrates, the interface between the accessory and the cable insulation, or the seal that keeps moisture out of the strand. Everything else about a termination - its shape, its colour, its catalogue photograph - is secondary to how well it manages those three jobs.
This article explains what separates a reliable silicone cold-shrink termination from an ordinary one, and what to look for when you evaluate a supplier. It is written for engineers, distributors and EPC buyers who have to make that judgement from a datasheet and a test report rather than from a decade of field experience.
---
# 1. The three jobs a termination has to do
-Field control. At the point where the metallic screen is cut back, the equipotential lines crowd together and the local field strength rises by an order of magnitude. A termination has to redistribute that field - either geometrically, with a stress cone, or dielectrically, with a semi-conductive deflector - so that no point in the insulation exceeds its design stress.
-Insulation withstand.The termination must carry the full impulse and power-frequency voltage with margin, at operating temperature, for the life of the circuit.
-Sealing. Water ingress into the conductor strand is cumulative and irreversible. Once moisture migrates along the strand, it feeds water trees in the cable insulation, and the failure that follows is usually attributed to the cable rather than to the accessory that let the water in.
A termination that does all three well is unremarkable in service. That is the point: the best accessory is the one nobody thinks about for twenty-five years.
---
#2. Why elastic recovery beats heat
-A cold-shrink termination arrives factory-expanded onto a removable support core. Installation consists of positioning the body over the prepared cable and pulling the core out; the silicone recovers its moulded dimensions and clamps onto the cable.
-The engineering consequence is that interface pressure is set in the factory, not on site. It is a function of the expansion ratio designed into the mould and the elastic memory of the compound. The installer's skill affects whether the termination is positioned correctly, but not how hard it grips.
-Heat-shrink works the other way round. The sleeve is expanded at manufacture, then shrunk on site by torch or heat gun. Final interface pressure depends on how evenly and how far the operator heats the material - which is why two terminations from the same box, installed by two different crews, can behave differently over twenty years.
| Criterion | Cold-shrink (silicone) | Heat-shrink (polyolefin / EVA) |
| Installation energy | None - pull the support core | Open flame or heat gun |
| Interface pressure | Fixed by factory expansion ratio | Depends on operator technique |
| Confined spaces, tunnels, gas-hazard areas | Suitable - no flame, no fumes | Hot-work permit and ventilation required |
| Low ambient temperature | Installs in cold conditions | Heating becomes difficult and unreliable |
| Risk to cable insulation | None - no heat applied | Local overheating can damage insulation |
| Long-term behaviour | Thermoset elastomer, no softening | Thermoplastic, can soften at elevated temperature |
For switchgear rooms, cable trenches and tunnel work, the absence of a hot-work permit is often the deciding commercial factor before any electrical argument is made.
---
# 3. Silicone versus EPDM: the property that actually matters
-Both silicone and EPDM are used for MV accessories, and both have adequate dielectric strength. The difference that shows up in service is surface behaviour under wet and contaminated conditions.
-Silicone rubber has a low surface energy, so water beads rather than filming across the surface. More importantly, if the surface is degraded by dry-band arcing, silicone can migrate its low-molecular-weight components to the surface and recover its hydrophobicity. EPDM does not recover in the same way: once a conductive water film forms, leakage current concentrates, dry-band arcing follows, and the erosion propagates.
-This is why silicone dominates outdoor terminations in polluted, coastal and high-humidity environments. It is also why the material specification - liquid silicone rubber rather than a general-purpose grade - matters more than the headline "silicone" on a datasheet.
Silicone also holds its elasticity across a wider temperature band than thermoplastic alternatives, which matters for a component that must maintain radial pressure through thousands of load cycles.
---
# 4. The interface is where the margin is won or lost
Elastic recovery only produces a reliable interface if there is enough material to generate and sustain pressure. Two parameters describe that, and both are easy to check with a scale and a calliper before you buy:
- Wall thickness of the insulating body
- Weight per kit, compared with equivalent products from other suppliers
-Thicker wall means three things at once: a higher recovery force at the interface, more thermal mass to absorb short-circuit heating, and a larger insulation margin around the stress-control region. Weight is a crude proxy, but a useful one - material that is not there cannot insulate.
-The pressure also has to persist. Silicone compounds differ in **compression set**: the permanent deformation left after long-term compression. A compound with poor compression set relaxes over years, interface pressure falls, and a void opens between the accessory and the cable insulation. That void is where partial discharge begins.
---
# 5. Why a built-in semi-conductive layer is not a detail
-In a cold-shrink termination, the semi-conductive layer that performs stress control is moulded integrally with the insulating silicone, not applied afterwards as a paint, tape or separate sleeve.
-The reason is interfacial. Two separately applied dielectrics almost always leave micro-voids at the boundary, and a void inside a high-field region is a partial-discharge site from the first energisation. An integrally moulded layer removes that boundary entirely: there is no interface to delaminate, no adhesive to age, and no dependence on how carefully a field installer aligned a tape.
-When you inspect a cut section of a termination, the semi-conductive layer should read as a continuous black band bonded to the insulating wall, uniform in thickness around the full circumference. Any step, wrinkle or gap at that boundary is a field concentration point.
---
# 6. Surface quality is a process indicator
The external surface of the sheds is not cosmetic. Tracking and erosion start at surface defects: a mould parting line with a raised burr creates a dry band, and a dry band is where arcing begins.
A termination that comes out of the mould with a glossy surface and a parting line flush to the surrounding material is evidence of two things - a well-maintained tool and a controlled cure. A part that needs polishing to look acceptable is evidence of the opposite, and polishing itself can leave directional scratches that are worse than the seam it removed.
Ask a supplier whether the parting line is flush as moulded. The answer tells you more about process control than any ISO certificate.
---
# 7. Reading a test report: the tests that actually discriminate
Almost every supplier can show a type test report. What separates them is *which* conditions were tested and *what the measured values were*.
- -Partial discharge at elevated temperature.Partial discharge measured at ambient is the easy case. A termination that holds ≤10 pC at 15 kV when the conductor is at 95–100 °C is a much stronger statement, because thermal expansion loads the interface exactly where voids tend to open. If a report shows only ambient PD, the hot case has not been demonstrated.
- -Both conductor and screen short-circuit tests.The conductor test proves the body survives the thermal pulse; the screen test proves the earth fault path does. Reports that show only one of the two are incomplete.
- -Outdoor-specific tests.Humidity, salt fog and immersion are what separate an indoor body from an outdoor design. A salt-fog endurance run is the closest laboratory proxy for coastal and industrial pollution service.
For reference, one 8.7/15 kV kit tested by CEPRI to GB/T 12706.4-2020 and IEC 60502-4:2023 recorded 2.0 pC at ambient and 1.7 pC at 95–100 °C, 52.09 kA for 2 s on the conductor, 3.51 kA for 1.04 s on the screen, 178.84 kA dynamic, and 1000 h of salt fog - the kind of numbers that indicate margin rather than bare compliance.
---
#8. Selection and installation notes
- Match the kit to the cable, not to the voltage class alone.** A 10 kV class kit covers 8.7/15 kV, but the cross-section range and core count must match the actual cable. A 25–50 mm² kit will not seal onto a 240 mm² cable, however correct the voltage.
- Indoor and outdoor bodies are different parts.Outdoor versions use longer, larger sheds for creepage under rain and pollution. Substituting an indoor body outdoors is a common and expensive mistake.
- Core count matters. Single-core and three-core cables need different stress-control geometry at the breakout.
- Respect shelf life. Silicone bodies are pre-expanded onto a support core that creeps with time. A kit stored beyond its stated validity - typically two years - may not recover to design dimensions.
- Keep the interface clean. The single most common installation defect is contamination between the cable insulation and the accessory body. Wipe with the supplied cleaner, install immediately, and do not touch the interface surface with bare hands.
---
#8. Five questions to ask a supplier
- What is the measured partial discharge at 95–100 °C, not just at ambient?
- Is the semi-conductive layer moulded integrally with the insulation, or applied separately?
- What is the wall thickness of the insulating body, and the net weight per kit?
- Which outdoor tests were run - humidity, salt fog, immersion - and for how long
- Is the mould parting line flush as moulded, without post-polishing?
Jinneng Electric Power Technology (Hubei) Co., Ltd. manufactures silicone cold-shrink terminations and joints for 8.7/15 kV, 12/20 kV and 26/35 kV systems, with type test reports issued by CEPRI to GB/T 12706.4-2020 and IEC 60502-4:2023.
---

